![]() Once testing of the latest upstream kernel is complete, please mark this report's Status as Confirmed. Please note, an error to install the kernel does not fit the criteria of kernel- bug-exists- upstream. If the mainline kernel does not fix the issue, please add the following tags: Where X, and Y are the first two numbers of the kernel version, and Z is the release candidate number if it exists. If this issue is fixed in the mainline kernel, please add the following tags by clicking on the yellow circle with a black pencil icon, next to the word Tags, located at the bottom of the report description: Once you've tested the upstream kernel, please comment on which kernel version specifically you tested. ![]() you couldn't boot into the OS) please make a comment in your report about this, and continue to test the next most recent kernel version until you can test to the issue. If the latest kernel did not allow you to test to the issue (ex. This will allow additional upstream developers to examine the issue. com/~kernel- ppa/mainline/ ?C=N O= D (the release names are irrelevant for testing, and please do not test the daily folder)? Install instructions are available at https:/ /wiki.ubuntu. Once this is in place, at your earliest convenience, could you please test the latest upstream kernel available from the very top line at the top of the page from kernel. no out-of-tree modules) if you need to preserve the original install. Randy Syring, the next step would be to install Ubuntu to another partition with default settings (i.e. version: Mac-189A3D4F975 D5FFCĭmi.modalias: dmi:bvnAppleInc. asset.tag: Base Board Asset Tag#ĭmi.chassis. UpgradeStatus: Upgraded to trusty on (534 days ago)ĭmi.bios.version: MBP111. Linux- backports- modules- 3.13.0- 57-generic N/A Linux- restricted- modules- 3.13.0- 57-generic N/A efi.signed root=ZFS=/ROOT ro libata.force=noncq cryptopts= target= cryptdev, source= /dev/disk/ by-uuid/ 6993c5ec- 7308-420d- bbe2-1ed18c15e2 bc,discard boot=zfs initrd= \initrd. ProcKernelCmdLine: \vmlinuz- 3.13.0- 57-generic. InstallationMedia: Xubuntu 13.10 "Saucy Salamander" - Release amd64 (20131016) ![]() InstallationDate: Installed on (690 days ago) NonfreeKernelMo dules: wl zfs zunicode zcommon znvpair zavl dmesg on my friend's MBP does not show those messages. The "Timeout while waiting" messages are suspicious to me. ![]() usb 1-1.4: new low-speed USB device number 10 using xhci_hcd usb 1-3.3: new full-speed USB device number 9 using xhci_hcd usb 1-3.2: new full-speed USB device number 8 using xhci_hcd usb 1-3.1: new full-speed USB device number 7 using xhci_hcd usb 1-1.4: new low-speed USB device number 6 using xhci_hcd usb 1-1.2: new low-speed USB device number 5 using xhci_hcd usb 2-1.1: new SuperSpeed USB device number 6 using xhci_hcd usb 1-5: new full-speed USB device number 4 using xhci_hcd usb 1-3: new full-speed USB device number 3 using xhci_hcd usb 1-1: new high-speed USB device number 2 using xhci_hcd xhci_hcd 0000:00:14.0: Timeout while waiting for address device command usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd usb usb2: Manufacturer: Linux 3.13.0-57-generic xhci_hcd xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2 usb usb1: Manufacturer: Linux 3.13.0-57-generic xhci_hcd xhci_hcd 0000:00:14.0: cache line size of 256 is not supported xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1 xhci_hcd 0000:00:14.0: xHCI Host Controller The last point made me look closer at the xhci_hcd dmesg | grep xhci_hcd * Uses the following drivers on my friends MBP: sd, usb-storage, usb, xhci_hcd All issues reported here seem to be the same regardless if I use 3.13 or 4.2. * Device 05ac:8406 does not show up in dmesg * Does not display any messages in dmesg when an SD card is inserted I have a friend with an identical Macbook Pro and his SD card reader does work in SystemRescueCD * does not work in SystemRescueCD running kernel 3.14.56- std461- amd64 I have a Macbook Pro (MBP) Retina 11,1 with an SD card reader that will not work.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |